BRADLEY SMOKER | "Taste the Great Outdoors"

Smoking Techniques => Hot Smoking and Barbecuing => Topic started by: Tommy18938 on January 16, 2020, 12:20:54 PM

Title: 10 Pd Brisket and Pork Butt
Post by: Tommy18938 on January 16, 2020, 12:20:54 PM
Hello all,

I have an Original Bradley that I've used several times for smaller single item smokes. I'm working on a larger smoke this Saturday and have a 10 pd brisket and 8 pd pork butt. On the brisket, the rack is a little too small and I was wondering how to cut it or just stuff it in. I've seen a couple videos showing a brisket folded up on a smaller rack and wanted to know your thoughts.
Now with the brisket on a higher rack, is it ok to pop in the pork butt on a lower one. If it is, how do I time this out? Is it in total volume or per piece. I'm also using a remote thermopro for the brisket. (only have 1 probe)Thanks in advance for your help.
Title: Re: 10 Pd Brisket and Pork Butt
Post by: Habanero Smoker on January 16, 2020, 02:29:22 PM
Hi Tommy18938;

Welcome to the forum.

If it is already trimmed, and doesn't fit on the rack you should be able to bend it so that it will fit on the rack. You can cut the brisket. If you haven't done so already, watch a few videos of trimming and separating the brisket into two cuts. The thing you need to be careful about is to make sure the brisket or the butt does not touch the back wall. If it touches the back wall grease will flow down the wall, onto the element and cause a fire.

It is alright to use the lower rack for the butt while the brisket is on one of the upper racks. Use your experience from your previous cooks, to get an idea of how long your cook will take. I find that briskets generally take longer than butts. The timing depends on how long it will take for your Bradley to get up to your target temperature. Once it gets to your target temperature the timing shouldn't be no longer than it would take to cook the largest piece.  For example, if you are smoke/roasting just a brisket, it may take two hours to get to your target temperature, and another 14 hours to finish - for a total of 16 hours. If you are smoke/roasting a brisket, and a butt; it may take 5 hours to get to your target temperature, then   an additional 14 hour for the brisket to finish; your butt should also be finished, if not sooner - for a total of 19 hours. Keep in mind the times I'm giving are just examples, your times may be longer. If you find yourself running short on time, you can transfer one or both pieces to the kitchen oven.

When smoking large fatty cuts of meat, change your water bowl at least every 3 hours, during the first 6 hours. Even if your water bowl looks full, it is most likely filled with fat.
Title: Re: 10 Pd Brisket and Pork Butt
Post by: Edward176 on January 16, 2020, 02:43:10 PM
Hello Tommy18938 and welcome to the forum. Let us know how your smoke turns out!!
Title: Re: 10 Pd Brisket and Pork Butt
Post by: Ka Honu on January 16, 2020, 03:57:41 PM
Unless you have a reason you want to separate it into parts or pieces, "hump" the brisket in the middle to fit the rack. As it cooks it will shrink enough to flatten itself. As Habs says, keep it away from the back wall.
Title: Re: 10 Pd Brisket and Pork Butt
Post by: iceman on March 01, 2020, 03:20:15 PM
Finally warmed up enough to do a smoke. Brisket was a little big but "humped it" like Ka Honu said and it worked our great. I know this post is old but how did your smoke turn out? I made enough for 10 people and there was only 6 of us. No left overs.  ;)