I smoke during the winter, and I get condensation to the point that the pucks get soft/wet and then they crumlbe and jam...
What can I do to stop this problem...
Howdy bcbobster. I do a lot of smoking in the winter also and have never had that problem. I do however keep the pucks in the pantry at a stable warm temperature with very low humidity. It's very important to keep them from absorbing excess moisture from the air. Hope this sheds some light on the problem. ;)
Nope, the condensation is when I'm smoking only... Is it because I like to keep the top vent totally closed???
I smoke pork roasts, takes about 5 hours to finish....
I live in the North East, and I never had this problem when I smoke during the winter months.
Sorry! I don't quite understand the problem. Does the problem occur during the time you are smoking, or is the condensation a problem on how you are storing the pucks?
In the smoking process only... The pucks are stored in my house, dry as a bone... But the heat builds up, I get condensation forming at the stack/heater area, and then the pucks seem to absorb the moisture and break up....
Quote from: bcbobster on April 06, 2006, 01:41:13 PM
Nope, the condensation is when I'm smoking only... Is it because I like to keep the top vent totally closed???
I smoke pork roasts, takes about 5 hours to finish....
I believe that is the cause of your problem. Not only moisture but smoke is backing out through your generator. This can cause serious problems, if you have smoke residue and moisture building up in your generator. Also with your pucks crumbling, you probably have a lot of wood chips in your generator housing, that plus the moisture that they absorb will cause corrosion and maybe eventually you could have an electrical short.
Keep your vent open at least far enough so that you do not see any smoke coming out from where the generator goes into the cabinet.
Bob of Ster,
It would be my some time mis-guided opinion here, you need to open the vent up to at least 1/4. For a couple of reasons, first is the moisture...leaving the vent closed is not going to help you keep your meat moist. All that moisture from the bowl and product has to go somewhere. It is not good where the moisture runs out the bottom it can get into the thermostat...it's got to if you have completely closed. I am sure that the smoke is coming out around the generator and along with that moisture. For some reason I think you might be getting a mess and start looking like a cookshack smoker. It is very important to releive the smoker of moisture. Hope this helps. Am I off base here?
Yes, I will try leaving the vent open abit... I will advise on my next smoke...
Quote from: bcbobster on April 06, 2006, 02:33:06 PM
Yes, I will try leaving the vent open abit... I will advise on my next smoke...
make sure it is open enough so no smoke is coming back through the smoke generator. I normally leave mine 1/4 to 1/3 open like MW and Habs said ;).
I go along with what MW, HS and BS said, I am sure this will be the cause of the problem. Particularly inportant are HS's comments about corrosion and electrical problems if too much condensation backs up in the system over time. :o
I had a similar problem with my Bradley, and it was definitely the vent. I had the misconception that keeping it closed would condense the smoke giving a stronger flavor, but it didn't really do anything other than make a big ol' mess.
Definitely, without any question, leave your vent open enough to prevent the smoke from backing out through the generator and that should solve your problem.
Quote from: manxman on April 07, 2006, 01:42:03 AM
I go along with what MW, HS and BS said, I am sure this will be the cause of the problem. Particularly inportant are HS's comments about corrosion and electrical problems if too much condensation backs up in the system over time. :o
I have a neighbors smoke generator that is now a pile of unidentifiable goo because of that. Sorry I misunderstood the problem but now that I know the circumstances it all makes sense. These guys are right on the money. John (my neighbor) has toasted two of his smokers because of this. (I think he's trying to support Bradley all by himself)! :D
QuoteJohn (my neighbor) has toasted two of his smokers because of this.
Perhaps he should be encouraged to post his experiences on the forum, step by step instructions of what not to do!! ;D
Quote from: manxman on April 07, 2006, 08:48:40 AM
QuoteJohn (my neighbor) has toasted two of his smokers because of this.
Perhaps he should be encouraged to post his experiences on the forum, step by step instructions of what not to do!! ;D
Right now he's kind of busy writing a book called "How to sink a river boat three times in a row without even trying". :o :D
Yep MW and Hab got her. I can't add anything (sorry :'() but wanted to tally another vote of what your problem most likely is. Crack that vent. In my early smoking I thought 'what a waste of smoke' when it comes billowing out the top. But after a bit, I realized that the Bradley produces an amazing amount of smoke, and you are not watching your $$$ go up in smoke, but producing the desired results. Hard to believe? - try cheese. Vent wide open for temp control and you absolutely still get the great flavour (here is where I would use the cool green tasty guy).
Not only should this help with your puck problem, but you will cut down on the cabinet condensation as well, where you get the black schag dripping on your meat and then dripping out the door onto your temp slider. You probably have smoke build up in your gen. I would not rip it apart unless you are comfortable, but I would give the burner a nice wire brush rub, and blow some forced air through the gen to get rid of wood residue.
I have noticed that juices dripping off of meat will land on the ramp and do the same thing. I see on the stainless model it has a hood on the ramp to shield the pucks from drippings landing on the ramp and jamming it.
Please if I asked a question and it sounds stupid...truly I'm not trying to be a smart butt Mark...I would just like to see you get your problem solved.
I have never experienced the problem...I know a couple years ago folks were putting the V-pan in wrong do to way the directions read...Could this be the problem? The V-pan has always protected mine with out a hitch. Or just maybe the meat product was touching the left side of the smoker and juices dripped down the side onto the edge of the unit? I could see where this might happen. And to add I'm sure you have read about the venting.
Please let me know I am interested to see what fixes it.
EVERYONE CALL YOUR MOM!
MW;
I'm thinking the same.
Mark;
I have the original BS, but I am not aware that the stainless steel model has a hooded heating plate. Are you sure you are not mistaking the Smoke Generator Adapter (which is stainless steel), for the generator that comes with the stainless steel models.