I'm going to try BB ribs for my first project. After reading a few posts in regards to this I have come to rhe conclusion it may not be the best choice but I have made my mind up. I've been looking at Iceman's post and I'm probably going that route. I'm going to be filling my 6 rack bradley with ribs and was wondering about rack rotation. Do you rotate top to bottom, or bottom to top, or just move each rack down or up one level every so often. I also need to know how often to rotate the racks. Thanks up front for your help. I know all of you know this from your past experiancesin regards to your first smoke, I'm really looking forward to my first meal out of the bradley. If you can think of anything else I need to know I would really appreciate that info to. Thanks Again
Snowmon
Don't recall Ice's full write up verbatum but I would say Rotate once an hour if/when you spritz with Juice. How many Bradley racks are you doing? Rotate so the very bottom rack always goes on top as that is the largest variation. Move the rest of the racks down 1.
I go bottom to top, and also reverse the racks front to back.
Do I wait till I start spritzing to start the rotation, or do I start the rotation from the begining?
Quote from: snowmon on July 18, 2008, 06:56:12 AM
Do I wait till I start spritzing to start the rotation, or do I start the rotation from the begining?
I really hate to open the tower. There's so much heat lost. Any other thoughts on this?
I've read somewhere here that some people use bricks to help the temp recover. I'm going to go by a couple and try it myself.
I use 'em. Regular red bricks double wrapped in HD foil. I don't want anything to get into the bricks but heat.
Definately make sure to reverse the racks from front to back also. The lower racks will get more heat on the back side due to the heating element location. I did not due that on my first load, and the ribs were browned more on one side than the other.
Icemans directions calls for spritzing after an hour and a half. The spritzing solution calls for apple juice and 1 part oil. Is it a 1 part to 1 part mixture or what???? I also would like some input in regards to smoke time for ribs. Thanks again. Any help with this would be greatly appreciated.
Quote from: snowmon on July 18, 2008, 12:04:56 PM
Icemans directions calls for spritzing after an hour and a half. The spritzing solution calls for apple juice and 1 part oil. Is it a 1 part to 1 part mixture or what???? I also would like some input in regards to smoke time for ribs. Thanks again. Any help with this would be greatly appreciated.
You can use 3 parts apple juice to 1 part oil. You don't have to use oil at all if you don't want to. It's not a set deal on the spritzing either. Some times I do and sometimes I don't. Depending on what smoker I'm using I usually run about 2 hours of smoke on the load then the rest is just cook time. Plan on around 6 hours or so total cook time at 200F. I like to boat them up after 4 total hours and drizzle the mopping sauce over them and cover tightly then finish them that way. Then I'll toss them on the grill over high heat for just a minute or two then serve. Just cook the ribs until the bone can be pulled out easily and you should be good to go.
You might want to take a look at the following, it was using Spare ribs and not Baby Backs, so the oven time would be roughly half. These came out F A N T A S T I C !!
http://forum.bradleysmoker.com/index.php?topic=7592.0
Should you flip the ribs over???
I never do. Bones down all the way.
Giz is correct bone down always.....! No flippe..bad llama!! ;D
C
Bones down here.
Quote from: FLBentRider on July 18, 2008, 07:29:21 PM
Bones down here.
Ditto that. Bones down, no flippy da ribby.
I got another stupid question. I read somewhere on this form about pulling the membrane off the back of ribs. If that is the case what is the best way to do this. I just got to eat some of my first project of ribs. They turned out pretty good. They were the first ribs I have ever ate without BB sauce and I loved them. Thanks to the receipe from Ice and everyone else that gave me advice. The bradley and everybody on this form is awsome!
It's a good idea to pull the membrane off. I typically grab a small sharp pairing knife and gently dig under the membrane on the bone side of the rib. Once I lift up a bit of the membrane and gently slide a finger (covered in a paper towel to make it easier) under the membrane, grip the membrane. Then pull hard and rip off as much of just the membrane a possible. Repeat if you don't get the entire membrane in one attempt. Then season . . .
;D ;D ;D
Snowmon,
Congrats on the ribs!
I use an inverted spoon to get at the membrane, then yank it off like the others. I also take the opportunity to remove any fat I can.
I use catfish skinning pliers. They are under $5.00 at Sportsman Warehouse. You can really get a good grip on the membrane with them.
Just lift and edge with tool of your choice and pull it off using a paper towel for grip.
I finally figured out it is all about temperature. As you approach room temp the membrane is pretty forgiving and easy to remove. :)
If that does not work drill some holes through the bones and mount it securely to the kitchen counter. The membrane can then be removed with a light touch and back and forth motion with the tip of a chain saw runnng at maximum rpm. ;)
Alternatively, score the dickens out of it with a knife... ;D
I was leaning toward using a power sander to get rid of the membraine, my sawsaw. ;D