smoke generator motor

[T-Dubbs]

If anyone knows where I can get a new motor for my smoke generator-let me know-thanx!

[iceman]

Burden Sales Surplus Center Has a FYJ50-8 Syncro motor that is a hair thinner but works just fine. It's Part # 5-1564-A. RPM 6 120VAC 33.4 milli amps. 4 watts. 6.7 in-lb stall torque. I paid $ 3.99 US for them and thet mailed them for me instead of UPS or FED X. Last I checked they had about 80 in stock. Phone 1 800 488 3407

http://www.surpluscenter.com/aboutUs.asp?UID=2005111815261539&catname=

Big or small you can smoke'm all!!!

[TY]

T-Dubbs, here is a couple of helpful hints. I see your post went out 3 times. I  have had that happen to me too. It seems my posts fail as the post times out on the computer so I retry to send it, only to find the original went thru. So now I just figure it goes thru even if it times out. When I do accidentaly do a multiple post of the same message, I found you can delete the duplicates real easy. Just go the FAQ section of the forum and select the "can I edit my post" topic for directions on how to edit/delete a post. Just trying to be helpful with a problem I have had too.

Lower Colorado River, AZ, It's a dry heat! ECV-2.0-Platrix

[iceman]

If you're the author of the post you can also just hit the trash can icon at the top of your post and delete it. You can delete all your posts on a subject except the original post that someone has already replied to.

[headgames]

Just wondering there Iceman . I ordered those motors and not really plug and play......... first they sent me some sanyos so watch that they say FYJ50-8 on the motor with a white label .  if they send you the green label ones just call them their customer service people were AWSOME  sent me new motors same day and no charge .

Any way Ice man when I try and install those motors I have to file the shaft down first .  the diamter is right but the flat part is too thick , am I the only one with the issue ? if so I will make my metal drive arm hole bigger . but I hate to if its just my batch of motors .  also there is no true center hole in the shaft like the original its a open D shape opening for about a 1/8" then divided verticaly with the flat part of the D the horizon.  When I put my original screw in it goes to one side and before it snugs it cracks the shaft .   Let me know thanks

If ya go home hungry.........You were at the WRONG HOUSE !

[headgames]

DA ......... feeling like a  dumb arse now  looked at my motors again they now sent a TYJ50-8.  WILL CALL THEM AGAIN..... SORRY ICEMAN ..

Every thing must be the same except that shaft ...  later guys




If ya go home hungry.........You were at the WRONG HOUSE !

[iceman]

#*!!!XX##**!! this dang timing out lost my first reply and sent it to the ozone layer[:(!] Anyhow headgames hope this one works. Sorry to hear about the motor shipment getting messed up. I apologize for misleading you about the plug and play thing. Your right about the flat side of the shaft being to big. I didn't mess with the file or grinder. I just heated the end of the swing arm up with a propane torch and slid the thing on. After it cooled down I melted the remaining part of the shaft that was sticking up with a soldering iron back into the center of the shaft then filed it flush. I drilled a small pilot hole back in the center of the shaft and reinstalled the retaining screw. I think you could heat the swing arm up over a stove flame if a torch isn't available. Hope this clears things up my friend. Let me know how the shipment turns out because I just ordered another motor myself. I think most folks out there could handle this repair if the unit is out of warranty. Take care.[:D]