I've just received my PID, a single. I printed the manual and have been reading through it before I set up. I see there are 2 methods to connect it. A one wire and a 2 wire. Are there any advantages of one over the other and any disadvantages.
Do you have the OBS or DBS smoker?
Mine is a DBS. The manual says the 1 wire is for the OBS but that's the only way I can hook it up. Using the 2 wire I'll have to order another cable.
If you have an extra computer cord you can use that. Hooking it up with one cord, you will need to reset the Bradley timer if your smoking/cooking more than 9:40 minutes.
Got lots of cord laying around. I'll have to see what I come up with. If nothing works I can live with the 9:40 until a new cord arrives.
I use 2 cords with mine, the element plugs directly into the Auber and I plug the SG to an AC outlet, that way the Auber is directly controlling the element instead of through the bradley digital, don't know if it matters just seemed logical to me, had lots of computor AC cords laying around anyways, actually thinking about it now if you use 1 cord with the digital it wont work cause as soon as the auber cycles off the digital will shut down, yes You need 2 cords for the digital-I believe.
Wouldn't you know it. I've computer cables coming out my ***** but no AC power cable. I'll check with by daughter and her better half later this morning (there computer gurus and geeks). They have more stuff, computer related, than you can shake a sausage at ;). I've checked the Auber site and can't find where I can order the cable by itself. It was included when you order the PID. Might have to send an e-mail or check with a computer store and see if I can find an AC cable. I should have read more closely when I ordered it originally :-[.
Got a power cord this morning and hooked everything up. Am running a test as I type. Running the sensor through the door seems problematic to me. Too many wires coming through the door. Probably get in the way when you're doing something with the meat. Thought I might just drill a hole in the top of the smoker, fit the sensor through it and tape up the hole and to hold the wire. Any thoughts?
I just run mine through the vent.
Sometimes I use the door, sometimes I use the vent.
It depends on what I am smoking.
I can't use the vent. I have my smoker in the garage and it's vented to the out side. The venting is connected to the top of the smoker. This is what mine looks like
(http://img.photobucket.com/albums/v481/candlelake/picture001.jpg)
I would just run it through the door then.
After using the PID for a few smokes, I don't use the the tower probe from my Maverick to much and just rely on the PID.
One less wire that way.
;D
As I said earlier, I ran a test and as far as I could tell the PID worked perfectly. What I noticed though, was the temperature reading on the bradley wasn't close. I should say that I had a meat probe in the smoker too and it's temps were identical to the PID. The smoker showed a temp 20* higher. I used to wonder why it took longer to get food to IT I wanted. Now I think it's because the smoker wasn't as hot as it said it was.
Quote from: HawkeyeSmokes on February 15, 2010, 06:47:24 PM
I would just run it through the door then.
After using the PID for a few smokes, I don't use the the tower probe from my Maverick to much and just rely on the PID.
One less wire that way.
;D
My PID is only a single probe. I'll still use the temp probe to check meat temps.
Quote from: RAF128 on February 15, 2010, 06:56:39 PM
Quote from: HawkeyeSmokes on February 15, 2010, 06:47:24 PM
I would just run it through the door then.
After using the PID for a few smokes, I don't use the the tower probe from my Maverick to much and just rely on the PID.
One less wire that way.
;D
My PID is only a single probe. I'll still use the temp probe to check meat temps.
I have the single probe Auber to. I just use the meat probe on my Maverick.
I have the old Auber and with the maverick I use both probes for the product and totally rely on the PID for the cabnet temp.
Quote from: OU812 on February 16, 2010, 11:17:02 AM
I have the old Auber and with the maverick I use both probes for the product and totally rely on the PID for the cabnet temp.
OU, you have the 73 and using both as product probe? Kewl
Quote from: classicrockgriller on February 16, 2010, 11:21:17 AM
Quote from: OU812 on February 16, 2010, 11:17:02 AM
I have the old Auber and with the maverick I use both probes for the product and totally rely on the PID for the cabnet temp.
OU, you have the 73 and using both as product probe? Kewl
Yep
With the PID there aint no reason to monitor the cabnet temp anymore.
Quote from: OU812 on February 16, 2010, 11:49:15 AM
Quote from: classicrockgriller on February 16, 2010, 11:21:17 AM
Quote from: OU812 on February 16, 2010, 11:17:02 AM
I have the old Auber and with the maverick I use both probes for the product and totally rely on the PID for the cabnet temp.
OU, you have the 73 and using both as product probe? Kewl
Yep
With the PID there aint no reason to monitor the cabnet temp anymore.
Unless you are lazy like me and you want the remote temp. ;D
The ET 73 is a remote but it dont shoot through the tin coverin the smokin shed
so I have to check on it every now and then, got a bottle out there too. 8)
Ahhh, the real reason for checking on the smoker comes out! ;D
This afternoon I drilled a hole through the top of my BDS and slipped the sensor through it. The sensor is a couple of inches from the top and just above the 1st rack of my 6 rack. A little duct tape and it now all sealed up and sensor shouldn't move.
Quote from: RAF128 on February 16, 2010, 06:22:37 PM
This afternoon I drilled a hole through the top of my BDS and slipped the sensor through it. The sensor is a couple of inches from the top and just above the 1st rack of my 6 rack. A little duct tape and it now all sealed up and sensor shouldn't move.
not sure if you want it that high in the cabinet, I put mine more central to where most of my cooking is done, mind you I doubt there is much difference in heat from top to bottom just preferrence I guess
Quote from: leftcoast smoker on February 16, 2010, 06:28:53 PM
Quote from: RAF128 on February 16, 2010, 06:22:37 PM
This afternoon I drilled a hole through the top of my BDS and slipped the sensor through it. The sensor is a couple of inches from the top and just above the 1st rack of my 6 rack. A little duct tape and it now all sealed up and sensor shouldn't move.
not sure if you want it that high in the cabinet, I put mine more central to where most of my cooking is done, mind you I doubt there is much difference in heat from top to bottom just preference I guess
I find a fairly significant difference in temp from top to bottom especially with a large load. I would have it around the middle of the cabinet as well. With a top location, your lower rack positions will see temps 20 to 30 degrees higher (in my experiences) than the bottom and therefore the items on the bottom will cook faster especially toward the back of the cabinet where the heating element is located.
This is my toughts on a fixed probe.
I'm like Gizmo, I have a 4 rk and if I have a non/ful load, I don't use the bottom rack.
If i cook 2 things at a time, I use the second from bottom and the third rack.
If i cook 1 thing, I flip a coin betweeen the second from bottom and the third rack.
So, If i was gonna put a stationary probe in my Bradley,
It would be between the 2nd and 3rd rack.
PS, If I had a 6rk it would be close to the top to middle of the 3rd rack.
I was thinking that I do most of my cooking near the top 'cause I was to be as far away from the heat source as possible. I think it's hotter near the back of the tower than the front. Also didn't want the probe wire dangling through several racks. Gets ackward when you're pulling out racks. I can see a problem if I'm doing longer sausages. Bottom would be hotter than the top.